Matt Parkhouse is one of the recognized gurus of the Airheads Email List which is used to spread wisdom/knowledge/fixes/info amongst Airheads all over the world. I just lucked out in that he agreed to help with me with the swap and that he was close by.
I got there a little after 1030am, having had to return shortly after leaving home to retrieve my camera. Just as well I was running late since Matt was tied up with another Airhead owner of a stripped down 1977 R90S. It was part of a ground up restoration and I'll cover the pictures I took of them working on that bike in a later posting.
A bit after 1200 or so, Matt was finally free and ready for me. I rode Brigitta into Matt's yard and next to his shop. He got to work immediately and within a minute or so had the carb off the left side of the bike and into the shop.
Matt has done hundreds of these carb jobs so he moved fast. I tried to keep up with photos but really, I was trying to actually see him do the actual work for when I do the rebuild next time they're due. He made it look so easy but I was comforted to see even he used an assembled carburetor as a guide when it came to putting things back together! In fact, as I'd read online somewheres, he also recommends keeping one carb assembled while you work on the other when doing rebuilds. It prevents mixing parts up since some of them are "handed" in that they are made to be on the specific side's carburetor, otherwise you reverse their function/range of motion which is not good.
The part of the swap process, the removal of the throttle plate and the peened mounting screws which I'd feared doing alone the most, proved anticlimatic as the screws appeared to Matt not to be peened. He did start dremeling one of the them so I got to see how that's done. In the end though, not much dremeling was needed.
Here's the left Carb without the cover
Disassembly begins, note the broken end on the mounting post that caused all this to occur
Most of the parts, removed, they were cleaned as they were taken off
The new carb body
Most of the parts on the new carb body
Old floats back on, new pin in place as the old one was bent
Carb Needle and old float
Old and New Diaphragms comparison, old is near top of pic
New Carb Body in place
Matt Parkhouse/Guru and Brigitta
Matt's wife's R100/7, note the well worn seat! This one has 107,777 miles on it, Matt's got another airhead with over 440k on it! He rebuilds the engines about every 100k miles. You can bet this bike is in much sounder mechanical condition than mine is!
Once he had Brigitta put back together, there was some tweaking of the carb floats to be done as I'd bent them before to deal with the vagaries induced by the bent mounting pin for the floats. He got that squared away easily enough though and I took Brigitta out for a test ride to warm her up prior to Matt doing a carb sync.
Once I got back I watched Matt do a carb sync by shorting each spark plug in turn as he made adjustments to the opposing carburetor. It was simply amazing how he did it. His method, he says, is more accurate since it balances the whole power process and not just the vacuum as the manometer method I use does. He's made from a couple of used /5 spokes, two rods which attach respectively on each spark plug end, the other end connects to the spark plug cable. To short out the plug he wants to short, he just touches the rod with a screwdriver! Cool stuff. I wish I'd thought to take pictures of them.
He got the idle correct using these tools, now I know you're supposed to adjust it so that the respective carburetor just barely stays running. Again, he made it look so easy.
He then ran up the rpms to about 3000 with a throttle lock and quickly switching between spark plugs with his shorting screwdrivers balanced the carbs at speed as well! Amazing. No pics, I was just barely keeping up with him just watching and I did not want to miss the Master at work! He works fast since its not good to run the engine without air moving over the jugs!
Brigitta is running sweetly now, her throttle response is snappier I think and I'm having to relearn my shifting/throttle operation due to the changes for the better. She sounds great, a bit throatier actually. Matt did preemptively replace both carb diaphragms since they were coming close to needing replacement.
Not expensive either, the whole thing came to $139! Labor and parts! Matt will probably be the guy I take the transmission on Brigitta for rebuild when that's due. He's a great teacher and mechanic and I can see why he's recognized as a Guru amongst Airheads.
Thanks Matt!
No comments:
Post a Comment